Add to Favorites
Share

Hydraulic Press For SMC Satellite Antenna

  • Description
Product Detail

    1. the machine by the host, hydraulic system and electrical control system.

    2. equipment control system with adjustment, manual and semi-automatic three kinds of works. Works selected by the switch, the touch screen centralized control. Semi-automatic way "out" and "without" "vent" and "without the exhaust" and "micro-mold" process moves to choose from, number exhaust is adjustable.

    "Not out" process action, outside the Panel is provided with "top" and "back" buttons. A total of four separate sets of buttons (top speed using pressure-compensated variable displacement pump).

    Machine: this machine is equipped with an independent double ejector, double core pulling devices, in-mold ejector is equipped with synchronism system so that mold is stable and reliable. (In-mold ejector is equipped with 6 sets of independent joints M16) compressor are outside organic "top out" "sent back" oil system interfaces with high pressure hose (compressor external circuit to provide each of the relevant connection parameters, such as size and pressure).

    3. equipment of hydraulic control system uses the integrated valve cartridge. The system is compact, sensitive and reliable, strong contamination resistance, flow resistance, easy maintenance, long service life.

    4. the electrical control system of the machine adopts PLC programmable controller and touch screen control, machine tool process cycle can be realized. The system enables control of a more flexible, accurate and reliable. Can be handy on the slider on the screen such as stroke and pressure parameters are preset. And a removable console.

    5. the master cylinder seals are made of poly-quality seals, greatly extending the life of the seals, and avoid the opening of oil spills. More convenient to repair and replace the seal.

    6. equipment main power systems and fuel tanks filled with liquid on top of the host, you can enable the machine to reduce the floor area.

    7. equipment with safety maintenance platforms, mobile operator with hand operation button, hydraulic systems with overload protection device and circuit of hydraulic support insurance. Can effectively protect the machine and operator safety. Meets the requirements of technical safety conditions of hydraulic presses.

    8. equipment hydraulic system oil tank with hydraulic oil filter, oil level indicator, loop. To ensure normal oil temperature between 15-45 degrees Celsius.

    9. equipment with oil filter clogging, oil level indicator, oil and lubrication, and other fault and fault alarm function.

    10. equipment with separate oil filtering system, as soon as the power on, the system automatically loop over the tank oil filter, to ensure clean oil.

    11. the compressor pressure control proportional pressure control systems, and digital displays and digital control. Pressure measuring element uses a pressure sensor, voltage-controlled components using proportional relief valve, pressure is displayed via a touch screen display.

    12. slider stroke digital display, digital control, precision measurement and display of 0.1mm.

    13. equipment using electrical control box set button control, set touch-screen on the control box, equipped with a selector switch and button below the Control Panel, all kinds of fault alarm indicator and control instruments are placed at the top.

    14. system voltage requirements for 10 minutes, less than 1Mpa, open pump fill pressure is not allowed. Process action with mold-blown gas in action.

    15. in the compressor tank located on a pump, (for the tank, a new oil and oil) independent control buttons, in the tank is on the bottom and pump the primer a 1 m high from the ground under the 1-inch drain pipe and tubing (1.3 m high above the ground where each piece of tubing plus a quick opening valves).

    16, the outside ejection: this machine is equipped with an independent double ejector, double core pulling devices, in-mold ejector is equipped with synchronism system so that mold is stable and reliable.

    17, pressure compensation device: equipped with new automatic energy-saving compaction systems can achieve a constant pressure for a long time and very little energy. System does not heat up.

    18, flexible pressure relief device: device for speed, pressure conversion process without shocks, smooth and reliable equipment operation.

    19, die device: the device has no pressure slow down function, does not damage the mold when the new die or change mold, maximum protection of mold.

    20, section air function: in front of the press mould sometimes need to vent, there are selection buttons on the touch screen to determine if an exhaust. Gas parameters can be set according to technological requirements, time can be divided into eight segments were deflated.

    Paragraph 21, holding function: automatic pressure holding sessions in several document conversions can improve the surface quality of the workpiece, usually can be divided into three segments.

    22, rapid pressurization function: press clamping set pressure is reached in a short time before, this function is the key to whether the workpiece up class-a surfacing.


Send your message to this supplier
To:  

HIL heavy technology limited

* Content:  

For better quotations, include:

- A self introduction

- Special requests, if any

Quantity:  

  
You May Like
Not exactly what you want? One request, multiple quotations Get Quotations Now >>